8 Layer PCB  Stack Up 

8 Layers PCB Board

8 layers Printed circuit board is generally installed into compact devices that have very restrict requirements of spacing, such as laptop motherboard, communication backplane, wearable watch etc. Due to its complexity and high cost of manufacturing, your 8 layers PCB fabrication should be handled by a reliable and experienced manufacturer. RayMing particularly targets on high-end PCB Manufacturing and assembly services for 10 years and a variety of customers witness the good quality and outstanding services. Our advanced production lines and responsive team would make you stay comfortable without any hassle since you place the order to us.

8 Layer Prototype PCB

The 8-layered Prototype FR-4 PCB is a circuit board with 8 layers that are stacked firmly together with predefined and dependable mutual connections between the layers. An 8 layer FR-4 PCBs has more complex structure. Twisted Traces is a reputable name in the field of manufacturing 8 layer prototype PCBs.

1. It has multiple power and ground planes- a digital ground plane helps prevent noise coupling.
2. It provides more planes for shielding signals from other signals on adjacent layers
3. More layers aid in routing signals that need matching
4. For analog signals especially those with RF, isolation and impedance control on traces is needed.

8 Layer PCB Instant Quote

In terms of a custom printed circuit board, our 8 layer PCB Instant Quote is the fastest turn-time at the best price that we have to offer. For on-demand pricing and ordering for your next printed circuit board project,Get Fast Quote you can contact our online customer support , or send email to sales@raypcb.com , Get 8 Layer PCB Quote Now !

With the constant development in the electronics industry, there has been improvement in PCBs manufacturing. This development has pushed PCBs towards increasing demands such as high speed, reliability, miniaturization, and better functionality which lead to the fabrication of multilayer PCBs. Multilayer PCB are available in different layers which include 4 layers, 6 layers, 8 layers, 10 layers, etc.

These PCBs consist of prepreg and double-sided or single PCBs that are stacked together to produce multilayer PCBs via a predefined mutual connection between them.  8 layer PCBs have gained popularity in different fields due to their exceptional electrical and mechanical properties.  

What is an 8 layer PCB?

An 8 layer PCB is a type of multilayer PCB that provides ample routing space for applications that need multiple power islands. This printed circuit board can help to enhance EMC performance by the addition of two planes.

This board is often mounted on compact devices like motherboard, wearable watch, backplane, etc. The increase in the cost of 8 layers PCB justifies the cost increase to achieve great EMC performance. An 8-layer PCB stackup is made up of four planes and four wiring layers connected by seven rows of dielectric material.

This PCB features a six-layer board with improved EMC performance. An 8-layer PCB is sealed with a solder mask at the bottom and top.

An 8 layer stackup should follow this pattern;

• Signal 1
• Ground
• Signal 2
• Power
• Ground
• Signal 3
• Power
• Signal 4

Materials Used for Fabricating an 8-layer PCB

The type of material an 8 layer PCB stackup consists of determines its performance. Thus, you need to be careful when choosing materials during the production process. To produce high-performance PCB, the best materials are substrates and conductive materials.

Substrates

Substrates like glass-epoxy materials help to insulate heat and signals. This helps you to handle the stackup better even in applications with high temperatures. Substrate materials have a great glass transition temperature that maintains the solidness of the PCB stackup.

Conductive materials

Copper is the most effective conductive material utilized in the fabrication process of the layer stackup. This material is an ideal option since it is a good conductor of heat, allowing proper signal transfers and minimizing heat accumulation on the device. Copper is also a cheaper alternative to other materials like silver and gold which are very expensive.

Advantages of 8 Layers PCB Stackups

8 layer PCB stackups offer a number of benefits which makes them an ideal alternative to other circuit board materials. Below are the advantages of these PCBs;

Minimize vulnerability: 8 layers PCBs reduce the vulnerability of a device, hence, increase the overall performance. This helps to shield the internal layers from noise, thereby reducing its vulnerability to external forces.

Reduce Radiation: This type of multilayer stackup helps to get rid of any radiation that might occur in high-speed applications. Unlike other stackups, 8 layers PCBs get rid of electromagnetic interference radiation.

Reduce the cost of operation: 8 layers PCB stackups are a cost-effective option. As regards replacements and cleaning, this stackup saves a lot of money. This means that an 8-layer PCB stackup requires low maintenance and is very durable.

Increase functionality: Opting for an 8-layer PCB will help to improve the speed and functionality of the devices they are used for. This printed circuit board is more reliable and functional in different applications. This PCB features over 4 layers of conductive materials that enhance the signal traces.

Applications of the 8 layer PCB Stackup

The 8 layer PCB stackup is the commonest type of stackup used in most appliances. This multilayer PCB is functional in several applications such as;

• Medical industry
• Automobile industry
• Manufacturing industry
• Chemical processing industry
• Aviation industry

Factors that Determine the Cost of an 8 Layer PCB Stackup

The fabrication of an 8 layer stackup costs money and there are several factors that contribute to cost.  This type of multilayer PCB stackup goes for about $3, however, certain factors determine the price.

Size of the board: The printed circuit board’s size has to do with the components in it. When there are more components on the board, the size of the PCB will increase. An increase in size will result in an increase in the fabrication cost of the circuit board.

Type of finish: This is another factor that contributes to the cost of an 8 layer PCB stackup. There are several finish options, so the type you choose will determine the PCB cost. Finishes like HASL, ENIG, ENEPIG, and IMM Sn are some of the popular finishes available.

Thickness: The thickness of a circuit board has to do with the materials that enhance the strength of the board. The thicker a circuit board is, the higher its price. The type of materials used in designing the PCB can determine the thickness of the board.

Size of the holes: If the board requires more holes, the cost of design and manufacturing will increase. Thinner holes will require more work before the circuit board can be produced.

Custom specifications: If you request specific configurations for your PCB design, this will increase its cost. More demands for configurations and customizations often increase the cost of producing circuit boards.

Guidelines for a Standard 8-Layer PCB Stackup

It is important you understand that some guidelines need to be met to achieve better performance. If you want a board that delivers better performance, there are guidelines that help you achieve that.

Proper routing direction: For an 8 layer stackup, the application requirements determine the number of layers of signal layers. In a case where there are six signal layers, there must be a perpendicular routing for the signal traces on the adjacent layers. This helps to reduce crosstalk, signaling the significance of various signal routines on the layer stackups.

Ground planes alignment: When the ground planes are split it may result in discontinuity of impedance. The components on the external layer must have extremely low impedance. Also, the components must connect to the internal ground planes through the vias.

Proper return path: You must ensure that the return paths are short enough to eliminate interaction with other components on the PCB.

Buried or blind vias: Another option to consider is utilizing blind or buried vias which will maximize the available space for component routing.  You must ensure that you can place the blind via on the board.

The Designing Process of an 8 layer PCB Stackup

The design process of a standard 8-layer PCB starts with a working design. This means that you should determine the type of 8-layer stackup you intend to use. This process will help you achieve a good stackup.

Creation of Idea

First things first, you need to determine the type of 8-layer PCB you need. You can then look for the best way to ensure the PCB stackup works. Select designing software you can use in the designing process. After that, develop a schematic i.e the PCB blueprint.

After developing a schematic, you will add every single piece of information you want to the stackup. The designing process will start with a blank page on the designing software.

Inclusion of component

You will start the designing process by including all the required details on the stackup. Specify the stackup’s shape and the number of layers. Then, you will ink all the details on the schematic. Ensure you review all information on the design and change what is necessary.

Then, you must define the designing rules and be certain that you follow them in the designing process. Don’t take any of these rules for granted so that it won’t affect the stackup’s performance.

Placement of component: At this stage, you will have to determine where other components will be placed. You will also have to determine how to arrange the layers and position drill holes. After this, all the route traces on the stackup will be positioned and then add labels and identifiers. Doing all of these will help you produce the HDI PCB design.

Frequently Asked Questions

What type of vias can be utilized in an 8-layer stackup?

There are different types of vias you can utilize in this type of multilayer stackup. These vias include buried vias, through-hole vias, vias in pads, microvans, and blind vias.

What kinds of surface finishes can be applied on an 8-layer PCB stackup?

The kind of surface finish on an 8-layer PCB determines its performance.  Some surface finishes you can choose for your 8-layer PCB include; immersion silver, electroless nickel immersion gold, organic solder ability preservative, lead-free hot air solder level, etc.

Conclusion

In recent times, the 8-layer PCB stackup has become popular. It is important to know that the application of this multilayer stackup is increasing over time. Opting for an experienced 8 layer PCB manufacturer is vital. They will offer you the best stackups that suit your application requirements.

An 8-layer PCB increases the working speed of complex appliances. This stackup improves the signal integrity of various designs. The design of an 8 layer PCB might take some time due to its complexity. An 8 layer PCB manufacturer must be well-detailed to create a good design.

Introduction

Printed circuit boards (PCBs) have evolved from simple single or double layer boards to complex multilayer boards with 6 or more layers to accommodate increasing component density and interconnectivity needs. 6 layer PCBs provide more flexibility for routing, plane separation and enable partitioning of circuits across layers.

However, designing the 6 layer stackup requires careful planning to utilize the layers effectively and avoid signal integrity issues. Key considerations include layer sequence, reference planes, material selection, copper weights, trace routing and via design. This article provides a detailed overview of 6 layer PCB stackup configurations, thickness calculations and manufacturing processes.

6 Layer PCB Stackup Configuration

The 6 conductive copper layers in a multilayer PCB are arranged in a predetermined sequence along with dielectric materials separating them. This is referred to as the layer stackup. Some key guidelines for 6 layer stackup design:

Layer Sequence

The conductors are numbered sequentially with the topmost layer being Layer 1. A typical 6 layer board stackup has:

Layer 1: Top/Component layer

Layer 2: Reference plane 1

Layer 3: Signal/Plane layer 2

Layer 4: Signal/Plane layer 3

Layer 5: Reference plane 2

Layer 6: Bottom layer

The top and bottom layers are used for component placement and routing. The inner layers are used for signals and reference planes.

Reference Plane Placement

The reference planes (ground and power) should be adjacent to routing layers for controlled impedance. A continuous ground plane next to signals is highly recommended.

Plane Splits

Reference planes can be split into analog and digital power sections to provide clean isolated supplies to sensitive analog circuits.

Symmetry

Symmetrical arrangement with reference planes above and below the mid layer provides optimal signal integrity. Asymmetrical stackups also used when needed.

Signal Routing

Route critical high speed or noise sensitive signals on inner layers sandwiched between planes. Avoid routing them on outer layers.

Breakout Vias

Use breakout/stub vias when routing inner layer traces to outer layers. Confines any stub effects.

Minimum Spacing

Follow board fabricator's design rule check (DRC) guidelines for minimum trace width, spacing, annular rings.

Common 6 Layer Stackup Arrangements

1. Symmetrical Arrangement

Copy code

Layer 1: Signal Layer 2: Ground Layer 3: Signal Layer 4: Power Layer 5: Signal Layer 6: Ground Layer 7: Signal

• Identical reference planes above and below mid layer
• Excellent signal integrity performance
• Widely used for digital, analog, RF designs

2. Asymmetrical Arrangement

Copy code

Layer 1: Signal Layer 2: Ground Layer 3: Signal Layer 4: Power Layer 5: Power Layer 6: Ground Layer 7: Signal

• Permits splitting power plane into sections
• Discontinuous ground planes affect signal quality
• Used when power distribution needs warrant it

3. Hybrid Arrangement

Copy code

Layer 1: Signal Layer 2: Ground Layer 3: Signal Layer 4: Ground Layer 5: Power Layer 6: Ground Layer 7: Signal

• Top and bottom ground planes for signals
• Mid power plane for splitting
• Balances signal integrity and power needs

6 Layer PCB Stackup Thickness Considerations

The overall thickness of a 6 layer PCB depends on:

• Copper layer thickness
• Dielectric layer thickness
• Number of lamination cycles

Copper Layer Thickness

Typical copper weights:

• Outer layers : 1 oz (35 μm)
• Inner layers: 1 oz or 0.5 oz (18 μm)
• Plane layers: 2 oz (70 μm) recommended

Heavier copper allows higher current carrying capacity.

Dielectric Layer Thickness

Typical dielectric layer thickness:

• 8 mil to 14 mil per layer
• 112-170 μm glass epoxy FR4 material
• Thinner dielectrics help minimize layer to layer capacitance

Lamination Cycles

A 6 layer board can be fabricated by:

• 2 lamination cycles - Bottom 3 layers pressed first, then top 3 layers
• 3 lamination cycles - Bottom 2, mid 2 and top 2 layers bonded

2 lamination cycles results in lower thickness variation versus 3 cycles.

Example 6 Layer PCB Stackup Thickness

Here is a sample 6 layer PCB stackup with typical thickness values:

Copy code

Layer Type Thickness Layer 1 - Top Signal 1 oz (35 μm) Layer 2 Ground 2 oz (70 μm) Layer 3 Signal 1 oz (35 μm) Layer 4 Signal 1 oz (35 μm) Layer 5 Power 2 oz (70 μm) Layer 6 - Bottom Signal 1 oz (35 μm) Dielectric 10 mil (254 μm) Total Thickness 6 Layers 110 mils (2.79 mm)

This is a symmetrical arrangement with approximately 110 mils (2.79 mm) total board thickness. Thinner dielectrics or copper can be used to reduce overall thickness. 8 layer boards typically range from 130 mils to 200 mils thickness.

6 Layer PCB Design and Manufacturing Process

The typical workflow for assembling a 6 layer PCB is:

1. Design

• Create schematic, layout, stackup in PCB design software
• Floorplan components, route traces, assign plane layers
• Design rule checks, signal integrity simulations
• Panelization, generate Gerber and drill files

2. Fabrication Data

The board fabricator reviews:

• Layer stackup and netlist
• Material selection
• Trace widths, spacing, annular rings
• Hole sizes, drill data, test points
• Panel drawing, breakaway tabs, fiducials

3. Inner Layer Processing

• Coat photosensitive dry film on copper clad laminate
• Expose dry film with circuit pattern using artwork/laser
• Develop and strip to form desired copper pattern
• Etch away unwanted copper, remove resist coating
• Clean and prepare layers for lay up

4. Lay Up

• Stack material layers as per 6 layer sequence
• Align layers precisely using fixtures and tooling pins
• Layup can be symmetrical or asymmetrical
• 2 or 3 lamination cycles followed

5. Lamination

• Layers bonded using high pressure and temperature
• Adhesive prepregs melt, flow and cure to form multilayer
• Bonds layers with intermediate dielectric
• Autoclave, hydraulic or thermal press used

6. Outer Layer Processing

• Drill holes for vias using NC drill machines
• Plate copper in hole walls to form barrel interconnects
• Pattern outer layers using similar imaging process
• Strip/etch to form signal layers with pads/traces

7. Solder Mask & Silkscreen

• Liquid Photoimageable Solder Mask (LPSM) applied
• Exposed and developed to form solder masking
• Silkscreen layer printed for component legends

8. Surface Finish

• Exposed copper plated with finish like HASL, ENIG, Imm. Tin
• Provides solderability and protects copper traces

9. Routing and Scoring

• Individual boards routed from panel using V-cut saws
• Breakaway tabs retain boards in panel during fabrication
• Test points added for probing circuits

10. Final Testing

• Bare PCBs electrically tested for shorts, opens using fixtures
• Automated optical inspection (AOI) to check flaws in assembly
• Impedance, signal integrity tests for critical boards

The fabricated 6 layer PCBs are then delivered to customers for component assembly and device integration.

Key Benefits of 6 Layer PCBs

Some of the key benefits of using 6 layers versus 4 layers:

• Additional signal layers for routing dense designs
• Ability to segregate power and ground planes
• Inner signal layers shielded from EMI/noise
• Controlled impedance environment for high speed signals
• Flexible power distribution to circuits
• Handles greater component density
• Overall smaller board footprint area

However, 6 layer PCBs have higher fabrication cost and complexity versus 4 layer boards. The additional layers should be leveraged judiciously from a design perspective to maximize the advantages.

Guideline for Selecting 4 Layer vs 6 Layer

Here are some criteria to decide between 4 and 6 layer boards:

Consider 4 layers for:

• Low-mid complexity designs
• Smaller board size < 150 cm2
• Only 2 or 3 major voltage domains
• Lower signal speeds < 1 Gbps
• Standard density interconnects
• Cost sensitive applications

Consider 6 layers for:

• Complex, dense component layouts
• Larger board area >200 cm2
• Multiple power domains and levels
• High speed signals > 2 Gbps
• Sensitive analog and RF circuits
• Easy routing of traces on inner layers
• Looser impedance control requirements

Conclusion

Designing an optimal 6 layer PCB stackup requires careful planning to utilize the layers effectively. Key considerations include selecting the right symmetrical or asymmetrical arrangement, intelligent plane splits, optimal dielectric materials, and routing critical signals on inner layers. Following sound stackup, impedance and routing guidelines helps utilize the full capabilities of the 6 layer board. The fabrication process also necessitates strict process controls to bond and pattern the multiple layers reliably into the finished PCB. With growing complexity and higher performance requirements, 6 layer PCBs are becoming the norm for many advanced designs today.

Frequently Asked Questions

Q1. What are the typical dielectric materials used in a 6 layer PCB?

Some commonly used dielectrics in 6 layer PCBs are:

• FR-4 Glass Epoxy - Most widely used PCB material
• Nelco N4000-13, N4000-6e - Low loss, Tg 140°C-150°C grades
• Isola FR408, IS410 – High reliability, lead-free compatible
• Arlon 85N, 55N - Low Dk for high frequency applications
• Rogers RO4350B, RO4835 - High frequency circuit materials
• Panasonic Megtron 6 - Low Df glass fabric material

Q2. What are the key considerations when selecting dielectric thickness in a 6 layer board?

Important factors when choosing dielectric thickness are:

• Target impedance - Thinner dielectrics help achieve higher impedance
• Layer to layer capacitance - Thinner dielectrics reduce capacitive coupling
• Glass content - Higher glass assists in controlling shrinkage
• Fabrication capability - Thinner materials may need more lamination cycles
• Signal frequencies - Thinner dielectrics better for higher frequencies
• Overall thickness - 8-10 mils per layer typical; high layer count thinner
• Mechanical stability - Thicker materials provide more rigidity
• Cost - Thinner materials generally costlier

What is 4 Layer PCB ?

A 4 Layer PCB (Printed Circuit Board) is a type of multilayer PCB that consists of four distinct conductive layers separated by insulating material. This design offers a balance between complexity and cost, making it a popular choice for many electronic applications.

Structure of a 4 Layer PCB

1. Top Layer: This is the outermost layer where components are typically mounted. It’s used for signal routing and component connections.
2. Inner Layer 1: Often used as a ground plane, providing a low-impedance return path for signals.
3. Inner Layer 2: Typically used as a power plane, distributing power throughout the board.
4. Bottom Layer: The second outer layer, also used for component mounting and signal routing.

These layers are separated by insulating material, usually FR-4 (a type of fiberglass epoxy resin).

4 Layer PCB  Capability :

Provide free DFM Checking , We can suggest 4 layer PCB stack-up

• Copper Thickness:  Max to 6 oz inner copper, 12 oz outer copper
• Min Hole: 0.15mm by mechanical drilling, 0.1mm by laser
• PCB Thickness :0.4mm – 6.5mm
• Surface Process: Immersion gold ,HASL-LF,Hard Gold,Immersion Tin
• Soler Mask: Green Yellon White Black or custom
• Silkscreen: White Black Yellow or custom
• Accept 4 layer PCB with Blind or buried hole
• 100% Testing

Learn more multilayer stackup reference:

How to Design a 4 Layer PCB Board

1. 4 Layer PCB Layer-out Guidance

Generally speaking, 4 layer circuit board includes the top layer, bottom layer, and two middle layers. The top and bottom layers are lay out with signal lines. The middle layer first uses the command DESIGN/LAYER STACK MANAGER to add INTERNAL PLANE1 and INTERNAL PLANE2 with ADD PLANE as the most used power layers such as VCC and ground layers such as GND that is, connect the corresponding network labels. Please note: you should not use ADD LAYER. This will increase MIDPLAYER, which is mainly used for multi-layer signal line placement.

PLANE1 and PLANE2 are two layers of copper connecting the power supply VCC and the ground GND. If there are multiple power sources such as VCC2 or GND2, first use a thicker wire in PLANE1 or PLANE2 or FILL. At this time, the wire or the corresponding copper ground is not visible, and the wire or filling can be clearly seen against the light.

To delimit the power or ground plane (mainly for the convenience of the PLACE/SPLIT PLANE command later), use PLACE/SPLIT PLANE to delimit the area in the corresponding areas of INTERNAL PLANE1 and INTERNAL PLANE2. VCC2 copper and GND2 copper should not be in the same PLANE as VCC. Please note that different network surface layers in the same PLANE should not overlap if possible.

Suppose SPLIT1 and SPLIT2 overlap in the same PLANE (SPLIT2 is inside SPLIT1). The two pieces are automatically separated according to the SPLIT2 border (SPLIT1 is distributed on the periphery of SPLIT). Pay attention to the pads or vias of SPLIT1 when overlapping; don’t try to connect SPLIT1 to the area of SPLIT2. At this time, the via holes in this area are automatically connected to the corresponding copper in the same layer. The DIP footprint components and plug-in parts that pass through the top and bottom boards will automatically get away from the PLANE in this area. Click DESIGN/SPLIT PLANES to view each SPLIT PLANES.

The Layer Setting and the Division of the Internal Electric Layer of Protel99

There are two types of electrical layers in PROTEL99. Open a PCB design file and press the shortcut key L, and the layer setting window appears. The one on the left (SIGNAL LAYER) is the positive layer, including TOP LAYER, BOTTOM LAYER, and MID LAYER. The one in the middle (INTERNAL PLANES) is the negative layer, also called the INTERNAL LAYER.

These two layers have different properties and usage methods. The positive layer is generally used for pure track lines, including outer and inner lines. The negative film layer is mostly used as a ground and power layer. In the multi-layer PCB board, the ground and power layers generally use the whole piece or several large copper partitions for the circuit. You must lay copper if you use the MID LAYER, also known as the positive layer. Paving copper will make the entire design data volume very large, which is not conducive to data communication and transmission, and will affect the HDI design refresh speed. With negative film, you only need to create a THERMAL PAD at the junction of the outer and inner layers, which is very beneficial for design and data transmission.

Add and Delete Inner Layer

In design, there are instances where it will need to add or delete layers. For example, the double-sided board is changed to a four-layer board, or the four-layer board with higher signal requirements is upgraded to a six-layer board, and so on. If you need to add an electrical layer, you can follow the steps below:

In the DESIGN-LAYER STACK MANAGER, there is a schematic diagram of the current stack structure on the left. Click the upper layer where you want to add a new layer, such as TOP, and then click ADD LAYER (positive film) or ADD PLANE (negative film) on the right to complete the addition of the new layer. If the new layer is a PLANE (negative film) layer, you must assign the corresponding network to the new layer by double-clicking the layer name.

There can only be one network assigned. Generally, a GND is sufficient for the ground layer. If you want to add a new network to this layer, such as a power layer, it can only be achieved by internal segmentation in the subsequent operations. Therefore, you first have to allocate a network with a large number of connections.

If you click ADD LAYER, a MID LAYER (positive film) will be added, and the application method is the same as the outer circuit. Suppose you want to apply a mixed electrical layer with both wiring and a large copper surface for power. In that case, you must use the positive layer generated by ADD LAYER to design (see the reason below).

Slip of the Inner Electrical Layer

If several groups of power supplies are in the design, you can use inner layer division in the power layer to distribute the power network. The command to be used here is PLACE-SPLIT PLANE. Then set the layer in the dialog box that appears, specify the network to be allocated for the split at CONNECT TO NET, and place the split area according to the copper paving method.

After the placement is complete, the holes with the corresponding network in this segmented area will automatically generate flower hole pads, which completes the electrical connection of the power layer. You can repeat this step until all power is allocated. When the inner electric layer needs to allocate more networks, it is more troublesome to divide the inner layer and require proper experience.

There is also a problem to be noted here: Excluding PLACE FILL, there are two electrical connection methods for large copper in PROTEL. The first is POLYGON PLANE or ordinary copper paving. This command can only be applied to the positive layer, including TOP /BOT/MID LAYER. The other is SPLIT PLANE or the internal electrical layer division. This command can only be applied to the negative film layer or INTERNAL PLANE. Attention should be paid to distinguish the scope of use of these two commands. Modify the command of split copper plating is EDIT-MOVE-SPLIT PLANE VERTICES.

2.How to design the stack up when designing a 4 layer PCB board?

In theory, there are three options.

Option 1:

One power supply layer, one ground layer, and two signal layers are arranged as below:

• TOP (signal layer);
• L2 (ground layer);
• L3 (power layer);
• BOT (signal layer).

Option 2:

One power supply layer, one ground layer, and two signal layers are arranged as below:

• TOP (power layer);
• L2 (signal layer);
• L3 (signal layer);
• BOT (ground layer).

Option 3:

One power supply layer, one ground layer, and two signal layers are arranged as below:

• TOP (signal layer);
• L2 (power layer);
• L3 (ground layer);
• BOT (signal layer).

Signal layer

Ground layer

Power layer

Signal layer

What are the advantages and disadvantages of these three options?

Option 1: The main stack-up design of the four-layer PCB is a ground plane under the component surface. The key signal is preferably the TOP layer. As for the layer thickness setting, here are the following suggestions: the impedance control core board (GND to POWER) should not be too thick in order to reduce the distribution impedance of the power supply and the ground plane to ensure the decoupling effect of the power plane.

Option 2: In order to achieve a certain shielding effect, the power and ground are placed on the top and bottom layers. However, this method has the following defects:

1) The power supply and the ground are too far apart. The plane impedance is large.

2) The power supply and ground plane are incomplete due to the influence of electronic component pads. Because the reference layer is incomplete, the signal impedance is not continuous.

In fact, due to a large number of surface-mount components, the power supply and ground of the solution can hardly be used as a complete reference layer. The expected shielding effect is excellent, but it is challenging to implement; it has a limited scope of use. However, in individual boards, it is the optimal layer setting option.

Option 3 is similar to option 1 and applies to the condition where the main device is wired in the bottom layout or the underlying signal.

1.6 mm standard 4 layer PCB stack-up 

0.2mm( PP thickness)+ 1.2mm(Double side core material)+0.2mm(PP thickness)=1.6mm 4 layer PCB stackup

1.2mm typical 4 layer PCB stack-up

1.2mm thickness=0.2mm PP & coil +0.8mm double side core material+0.2m PP with copper

How to Use Altium Designer10to Draw 4 Layer Board

If you could implement double side PCB, the same can be applied to 4 layer PCB boards. The following describes how to draw a 4-layer board based on a 2-layer board.

The above picture is a 2 layer board. The below shows two layers: the top and bottom layers. The layer is the signal layer, also known as the positive film, and can do circuit layout on this layer. Others include a mechanical layer, silkscreen layer, solder mask, and so on.

Below is the 3D drawing

In the English version, press and hold the ctrl + L keys to view frequently used layers.

As shown below:

The signal layer includes the top layer and bottom layer, and the mechanical layer includes 1, 13, 15 (of course, it can be added). The mask layer has top/bottom paste, top pad layer, or solder stencil layer, and top/bottom solder is the top or bottom solder mask to prevent it from being covered by green oil. There are two silkscreen layers below, top/bottom overlay. There are other layers, the keep-out layer used to define the shape of the board, the drill drawing layer, etc.

There is also an internal plane next to the signal layer, called the internal electric layer or negative film. Only layer division can be performed on this layer, and signal wiring cannot be performed.

Click Design — Layer Stack Manager in the menu bar, as shown in the figure below:

This is the layer manager. You can easily see the layer distribution in the above figure. This board has only two layers: the top and bottom layers, both of which are signal layers. There are two more options on the right. One is “Add Layer”, the other is “Add plane”. Add layer adds a signal layer, add plane adds an internal electric layer (negative film).

To add a layer, first select a base layer. Then click on “Add Layer” to add the signal layer under the top layer.

Then you can rename the added layer, such as VCC, and add another layer as GND, as shown in the following figure:

Back to the PCB interface, you can see that there are already 4 layers.

You already know how to create 4 layers, 6 layers, even 8 to 20 layers with the same operation.

When dividing the inner electric layer, we can only divide it and could not create a circuit layout, as shown in the following figure:

Adding the internal electrical layer is to add the “add plane” in the Layer Stack Manager.

The internal electrical layer split in the figure above can be split by drawing a line with the place—line command. After the split is completed, double-click to set the network label.

Pay attention to the distribution of components when splitting the internal electrical layer and distribute the same power supply in one area to facilitate the division.

The following is the signal distribution at different layers:

Top layer：

VCC layer：

GND layer:

Since the GND layer is a whole piece of GND, it is sufficient to lay the copper. Pay attention to maintaining the integrity of the GND layer.

Bottom layer:

When open all layers as below shown:

3D drawing：

Main points of 4-layer board wiring:

Pay attention to the distribution of power supply;

Pay attention to the signal line width setting and impedance control;

Distribution of layers, how to arrange 4-layer boards;

High-speed signal return problem;

Crosstalk between high-speed signals;

How to reduce the minimum loop and reduce the EMI problem;

Placement of decoupling capacitors;

If you learn to use Altium software to draw 4 layer boards, you can also use EasyEDA, Eagle, and KiCad to draw 4 layer boards.

2 layer vs. 4 layer PCB Prices

4 layer PCB board has GND and POWER layers in the middle of TOP and Bottom layers.

Features of the 4 layer board

1) Reference plane, impedance calculation can be done
2) Shorter return path
3) More layers, simpler design
4) Higher cost than 2-layer board

Based on the wiring density in the layout, look at the densest place of the flying lines, where there are crossovers. It is judged that at least 2 layers of wiring are required, and the cost (design multiple layers regardless of the cost), signal quality consider whether to choose 4-layer board.

After the layout, it is judged how many layers to use, mainly depending on the density of the signal and the place with the most flying lines.

Why Choose to Design 4 Layer PCB

1. When there is a BGA package, the outer 2 rows can be directly pulled out to go to the top layer. The third and fourth layers can be drilled to go to the bottom layer, and the fifth and sixth rows can be drilled to go to the bottom layer. However, the inside power and ground wirescannot go out, so an additional layer design is required, and two more layers are added.
2. The power lineblocks the signal line.
3. Whenline density is not high, you can use a 2-layer board, but you can choose a 4-layer board based on signal quality considerations.

Different Manufacturing Process

How Do You Make a 4 Layer PCB

The 4-layer board is laminated based on the double-sided board. When lamination, PP, and copper foil are added on both sides of the double-sided board, it is then pressed into a multilayer board through high temperature and high pressure. In short, the 4-layer board has an inner layer. In terms of the process, some lines will be etched through the inner layer formed by lamination. The double-sided board can be drilled after cutting the raw material sheet directly.

Technology Process difference

1. Double-sided PCB with HASL surface finished process:

Cutting material grinding → drilling → electroless copper → outer layer circuit → tin plating, etching tin removal → secondary drilling → inspection → printing solder mask → gold-plated → hot air leveling → printing silkscreen → outline processing → testing → inspection

2. How do you manufacturea 4 layer PCB:

Cutting material and grinding → drilling positioning holes → inner layer circuit → inner layer etching → inspection → black oxide → lamination → drilling → electroless copper → outer layer circuit → tin plating, etching tin removal → secondary drilling → inspection →print solder mask→Gold-plated→Hot air leveling→print silkscreen→routing outline→Test→Inspection

Price difference

PCB production costs are related to the actual area and specific technology requirements. If there are no special requirements, a 4-layer board’s cost is almost 1.8 to 2 times that of a 2-layer board. This is not a linear relationship. If the 4-layer board has impedance or even a blind buried hole design, the price difference is even greater.

Altium Designer 4-layer PCB Design Tutorial

This tutorial allows beginners to get started. The software I use is Altium Designer 13, but the basic operations are similar to other software.

1.Preparation

Create a new project file, create a related schematic file, and prepare the relevant PCB design. Create a new PCB file.

2.Set the layers

In the PCB interface, click the main menu Design and then click Layer Stack Manager

As shown below:

After clicking, the following layer manager dialog box will pop up. The default is double-panel in AD, so we see only two layers of circuit.

Now let’s add a layer. First, click Top Layer on the left, and then click the Add Plane button in the upper right corner of the layer manager to add an internal electrical layer. Because we are working with a 4-layer board using negative film, you need to add an internal electrical layer and not Add Layer. Afterward, a layer will be automatically added under Top Layer. Double-click the layer, and we can edit the related attributes of this layer, as shown in the figure below:

In the item corresponding to Name, fill in VCC and click OK to close the dialog box. Rename the layer to VCC as the power layer during design. In the same way, add another GND layer. Below is the figure after completion:

3.Import network

Back to the schematic interface, click the main menu Design ==> Update PCB Document.  As shown in the figure:

After finishing the layout of the components on the PCB drawing, draw the outline of the PCB on the Keep Out Layer, as shown below:

Modify the PCB drawing size to overlap the lines of the keep out layer. First, set the grid network width to 20mil. Then click the pad symbol in the shortcut toolbar, and move the mouse to the top left corner of the keep out layer. A circle should appear in the center of the pad. Click the arrow keys on the keyboard to move the pad (click in the left direction, click in the upper direction). Press the enter key, as shown in the figure:

Set the other four corners the same way.

Then click design -> board shape -> move board vertice, overlap the four points on the drawing with the pad placed just on the keep-out line, and click the right button.

Delete the pads on the four corners.

4.Set the inner electric layer; I have divided the inner electric layer in the process here.Then execute design -> layer stack management -> double-click the GND layer, and select the GND network in the NET NAME, which is defined as the GND layer (before, it was just a GND name).

Set the VCC layer: First, enter the VCC layer, use the line place -> line to divide the VCC layer (the closed line or both ends of the line are connected to the outer pullback line), divide into different NET layers, and then click on different areas to select different NET.

At this time, we can see a virtual circle around the pad of the corresponding internal electrical layer. The color of the cross on the pad represents the color of the corresponding internal electrical layer. For example, the inner layer GND is brown, and the cross of the pad is also brown.

p.s

The pullback automatically appears around the PCB drawing after the Layer Stack Manager is set. You can double-click the inner layer to set the pullback line width.

The cross of the pad only appears when the pad is placed on the corresponding net layer. If it is placed on other layers, it will not appear. As long as the cross passes through the VCC layer, it will appear.

What is a double sided PCB?

The 2 layer PCB ( double-sided PCB )is a printed circuit board with copper coated on both sides, top and bottom. There is an insulating layer in the middle, which is a commonly used printed circuit board. Both sides can be layout and soldered, which greatly reduces the difficulty of layout, so it is widely used.

To use circuits on both sides, there must be a proper circuit connection between the two sides, as shown in the pictures below. The “bridges” between such circuits are called vias. A via is a small hole on the PCB board filled or coated with metal, which can be connected with the circuits on both sides. Because the area of the double-sided board is twice as large as that of the single-sided board, the double-sided board solves the difficulty of the single-sided board due to the interlaced layout (it can be connected to the other side through the holes), and it is more suitable for more complicated circuits than the single-sided board.

We need electronic products with high performance, small size, and multiple functions, which promotes the development of printed circuit board manufacturing to be light, thin, short, and small. With limited space, more functions can be realized, layout density has become greater, and the hole diameter is smaller. The minimum hole diameter of mechanical drilling capacity has dropped from 0.4mm to 0.2mm or even smaller. The hole diameter of the PTH is getting smaller and smaller. The quality of the PTH (Plated Through Hole) on which the layer-to-layer interconnection depends is directly related to the reliability of the printed circuit board.

Double Layer PCB Production Manufacturing process

The production of double-sided board is more complicated than single-sided board. The main reasons are as follows:

(1) The top and bottom layers of the copper coated board/laminate must be layout

(2) The circuits on the top and bottom layers should be connected with PTH.

Particularly critical among these is the PTH, which is also the core process of double-sided board production. The so-called PTH is created by coating/plating a layer of metal on the inner wall of the via to connect the printed circuits of the top and bottom layers. At present, domestic PTH mainly adopts the electroless copper plating process in China. There are two types of electroless copper plating process:

① The thin copper is electrolessly plated first, then the whole board is electroplated to thicken the copper layer, and finally the pattern transfer is performed.

② The thick copper is electrolessly plated first, and then the pattern is transferred directly.

Both of these processes are widely adopted. However, the electroless copper plating method is harmful to the environment, and it will gradually be replaced by more advanced Black hole technology, tin/palladium direct plating technology, and polymer direct plating technology.

2 Layer PCB With HASL-LF /immersion gold surface production process

Cutting —> Drilling —> Sinking/1^ST Copper Plating —> Layout —> Pattern Plating/2^nd Copper Plating —> Etching —> Solder Mask —> Legend Printing —>Immersion Tin (or Immersion Gold) —> CNC Routing —> V Cut (some boards do not need this) —> Flying Probe Test —> Vacuum Packaging

Double-sided PCB with gold plating production process

Cutting —> Drilling —> 1^ST Copper Plating —> Layout —> Pattern Plating/2^nd Copper Plating —> Gold and Nickel Plating —> Etching —> Solder Mask —> Legend Printing —> CNC Routing —> V Cut —> Flying Probe Test —> Vacuum Packaging

Multilayer HASL-LF board/immersion gold board production process

Cutting —> Inner Layer —> Layer Stack —> Drilling —> Sinking/1^ST Copper Plating —> Layout —> 2^nd Copper Plating —> Etching —> Solder Mask —> Legend Printing —> Immersion Tin (or Immersion Gold) —> CNC Routing —> V Cut (some boards do not need this) —> Flying Probe Test —> Vacuum Packaging

Multilayer plate gold plate production process

Cutting —> Inner Layer —> Layer Stack —> Drilling —> Sinking/1^STCopper Plating —> Layout —> 2^ndCopper Plating —> Gold and Nickel Plating —> Etching —> Solder Mask —> Legend Printing —> CNC Routing —> V Cut —> Flying Probe Test —> Vacuum Packaging

1. Pattern plating process

Copper clad board/Laminate —> Cutting —> Punching and drilling benchmark —> CNC drilling —> Inspection —> Deburring —> Electroless thin copper plating —> Electroplating thin copper —> Inspection —> Brushing —> Filming —> Exposure and development (or curing) —> Inspection and repairing —> Pattern plating (Cn + Sn/Pb) —> Film removal —> Etching —> Inspection and repair board —> Nickel-plated and gold-plated plugs —> Hot melt cleaning —> Electrical continuity detection —> Cleaning —> Solder mask —> Curing —> Legend —> Curing —> Shape processing —> Washing and drying —> Inspection —> Packaging —> Finished product.

Thin copper —> Thin copper electroplating —> Electroplating thin copper can be replaced by a single process of electroless thick copper plating; both have their advantages and disadvantages.

The pattern plating —> etching method of double-sided board was typical in the 1960s and 1970s. The process of Solder Mask on Bare Copper (SMOBC) gradually developed in the 1980s, and has become the mainstream process especially in precision double-sided board manufacturing.

2. SMOBC process

The main advantage of SMOBC board is that it solves the short-circuit phenomenon of solder bridging between thin circuits. At the same time, due to the constant ratio of lead and tin, it has better solderability and storage properties than hot melt board.

There are many ways to manufacture SMOBC boards, including the SMOBC process of standard pattern electroplating subtraction and then lead-tin stripping; the subtractive pattern electroplating SMOBC process of using tin plating or immersion tin instead of electroplating lead-tin; the plugging or masking hole SMOBC process; additive method SMOBC technology; etc. The following mainly introduces the SMOBC process and the plugging method SMOBC process flow of the pattern electroplating method and then the lead-tin stripping.

The SMOBC process of pattern plating followed by lead-tin removal is similar to the pattern plating process, and changes only after etching.

Double-sided copper laminate —> According to the pattern electroplating process to the etching process —> Lead and tin removal —> Inspection —> Cleaning —> Solder mask —> Plug nickel plating and gold plating —> Plug sticking tape —> Hot air leveling —> Cleaning —> Legend —> Outline —> Cleaning and drying —> Finished product inspection —> Packaging —> Finished product.

3. Main process flow of the plugging method

Double-sided copper laminate —> Drilling —> Electroless copper plating —> Electroplating copper on the whole board —> Plugging holes —> Film (positive film) —> Etching —> Removing screen printing materials/Removing plugging material —> Cleaning —> Solder mask —> Plug nickel plating and gold plating —> Plug sticking tape —> Hot air leveling —> The following procedures are the same as above to the finished product.

The steps of this process are relatively simple, and the key is to plug the pores and clean the plugged solder mask.

In the hole plugging process, if the hole plugging solder mask is not used to block the holes and the screen printing imaging, but is replaced by a special masking dry film which is then exposed to make a positive image, this is the masking hole process. Compared with the hole plugging method, it fixes the problem of cleaning the solder mask in the hole, but it has higher requirements for masking the dry film.

The basis of the SMOBC process is to first produce the bare copper double layer board PTH, and then apply hot air leveling.

Pore mechanism

Drill holes on the copper-clad board first. It then undergoes electroless copper plating and electroplating copper to form plated through holes. Both play a crucial role in hole metallization.

1. The mechanism of electroless copper

In the manufacturing process of double-sided and multi-layer printed boards, it is necessary to metallize the non-conductive bare holes (NPTH), that is, to implement electroless copper to make them a conductor. The electroless copper precipitation solution is a catalytic “oxidation/reduction” reaction system. Under the catalytic action of metal particles such as Ag, Pb, Au, and Cu, copper is deposited.

2. The mechanism of copper electroplating

The definition of electroplating is to use a power source to push positively charged metal ions in a solution to form a coating on the surface of the cathode conductor. Copper electroplating is an “oxidation/reduction” reaction. The copper metal anode in the solution oxidizes the copper metal on its surface to become copper ions. On the other hand, a reduction reaction occurs on the cathode, and copper ions are deposited as copper metal. Both of them achieve the purpose of perforation through chemical exchange, and the exchange effect directly affects the quality of perforation.

Debris plug holes

In the long-term production control process, we found that when the hole diameter reaches 0.15-0.3mm, the proportion of plug holes increases by 30%.

1. The plugging problem in the process of perforation

When the printed board is processed, most small holes of 0.15-0.3mm still use the mechanical drilling process. In the long-term inspection, we found that impurities remained in the hole when drilling.

The following are the main reasons for drilling plug holes:

When a plug hole appears in a small hole, due to the small hole’s diameter, it is difficult to remove the impurities inside it by high-pressure water washing and chemical cleaning before copper plating, which prevents the exchange of the chemical solution in the hole during the electroless copper precipitation process and makes the electroless copper lose its effect.

When drilling holes, select suitable drill and backing plates according to the thickness of the laminate, keep the substrate clean, and do not reuse the backing plates. Effective dust collection (using an independent dust collection control system) is a factor that must be considered to solve the plugging hole.

Draw circuit diagram

1. There isa variety of dedicated PCB drawing software, such as Protel, etc., which can draw multilayer (including double-sided) circuit board diagrams. The positions of the layers are aligned, and there are vias to connect the layers.The circuit is connected to realize cross circuiting and facilitate typesetting. After the layout is completed, it can be handed over to a professional board factory to become a circuit board.

2. The double-sided circuit board should be drawn into the circuit schematic diagram in turn, which can be divided into two steps. Step 1: Draw the legends of the main components such as IC on the paper according to the position of the circuit board, arrange and draw the circuit of the pins and the peripheral components appropriately, and complete the sketch. Step 2: Analyze the principle and organize the circuit diagram according to the customary drawing method. You can also use the circuit schematic software to arrange the components and connect them, and then use its automatic typesetting function to organize.

The circuits on both sides of the board should be accurately aligned. You can use the tips of tweezers, the light transmission of a flashlight, and a multimeter to measure the connection and disconnection and determine the connection and direction of the solder and circuits. If necessary, remove the components to observe the layout.

What is the difference between single-sided PCB and 2 layer PCB ?

Single-sided and double-sided boards differ in the number of copper layers. Double-sided has copper on both sides of the board, which can be connected through vias. However, there is only one layer of copper on one-sided board, which can only be used for layout, and the holes made can only be used for SMT.

Single-sided board is the most basic PCB. The parts are concentrated on one side, and the circuits are concentrated on the other side. Because the circuits are only on one side, this kind of PCB is called single-sided. Single-sided boards have many strict restrictions on the design of the circuit (because there is only one side, the circuits cannot cross and must follow separate paths), so only early circuits use this type of board.

There is layout on both sides of a double-sided circuit board, but to use layout on both sides, there must be a proper circuit connection between the two sides. The “bridge” between such circuits is called a via. A via is a small hole filled or coated with metal on the PCB, which can be connected with the layout on both sides. Because the area of the double-sided board is twice as large as that of the single-sided board, it solves the difficulty of the single-sided board due to the staggered layout (it can be passed to the other side through vias), and is suitable for use in more complicated circuits than single-sided board.

1. Raw Material

Single-sided board: Has copper foil only on one side, such as TV board.

Double-sided board: There are copper traces on both sides, connected by conductive through holes. The price is generally 7 times different (not fully defined due to different materials). There is also a kind of false double-sided board in the industry, which has no through hole connection (much lower cost).

2. Process

Single-sided PCB board: The solder joints are concentrated on one side, and components are usually inserted on the other side. Some products still have SMD components on the copper-clad side. Double-sided board: Both sides can be layout, and both can have plug-in components or SMD components.

False double-sided PCB: Generally, only one side SMT and layout on the other side. The double-sided copper cladding is connected by circuit on both sides of the component foot.

3. PCB circuit board

Single-sided board: The metal circuit that provides the connection of the parts is arranged on an insulating substrate material, which is also a support carrier for installing the parts.

Double-sided PCB : When a single-sided circuit is not enough to provide the connection requirements of electronic parts, the circuit can be arranged on both sides of the substrate, and through hole circuits are deployed to connect the circuits on both sides of the board.

4. Production process

Single-sided board: CAD or CAM CCL cutting, drilling positioning —> Opening punching mold, making screen plate —> Printing conductive pattern, curing —> Etching, removing printing material, cleaning —> Printing solder mask pattern, curing —> Printing marking legends, curing —> Drilling and punching positioning holes, punching and blanking —> Circuit inspection, test —> Solder mask and OSP —> Inspection, packaging, finished product.

2 Layer PCB : AD and CAM CCL cutting/edging —> NC drilling —> PTH —> Pattern plating —> Full plate plating —> Dry film or wet film method masking or plugging holes —> (Negative pattern) (Positive pattern) —> Copper plating/tin lead pattern transfer —> Film removal, etching —> Tin and lead removal, plug plating removal, cleaning —> Printing solder mask/legends —> Hot air leveling or OSP —> Routing/punching shape —> Inspection/testing —> Packaging/finished products.

How do you make 2 layer PCB and precautions

At present, the mainstream circuit board assembly technology in the SMT industry is “full-board reflow soldering (reflow)”. Of course, there are other circuit board soldering methods, and this full-board reflow soldering can be divided into single-sided reflow soldering and double-sided reflow. Single-sided PCB reflow is rarely used now, because double-sided reflow can save space on the circuit board, which means that the PCB can be made smaller. For that reason, most of the boards seen on the market now belong to the double-sided reflow process.

Because the “double-sided PCB reflow process” requires two reflows, there will be some process restrictions. The most common problem is that when the board goes to the second reflow, the parts on one side will be falling due to gravity, especially when the board goes to the reflow zone at high temperatures.

Generally speaking, smaller parts are recommended to be placed on the first side to pass through the reflow oven, because the deformation of the PCB will be smaller on the first pass through the reflow oven, and the precision of solder paste printing will be higher, so it is more suitable to use smaller parts.

Secondly, the smaller parts will not fall off the second time through the reflow oven. Because the parts on the first side will be placed directly on the bottom side of the circuit board, when the board re-enters the reflow zone at high temperature, they are less likely to fall off the board due to excessive weight.

Third, the parts on the first side must go through the reflow oven twice, so their temperature resistance must be able to withstand the heat of the oven twice. The general resistance capacitor is usually required to be able to pass the high temperature at least three times. This meets the requirement that some boards may need to go through the reflow again for repair.

Which SMD parts should be placed on the second side through the reflow furnace? This should be the focus.

Large components or heavier components should be placed on the second side to pass through, to avoid the risk of parts falling into the reflow furnace.

LGA and BGA parts should be placed on the second side through as much as possible, so as to avoid unnecessary remelting risks during the second pass, and to reduce the chance of empty/false soldering. If there are smaller BGA parts, it is recommended to put them on the first side through the reflow furnace.

Placing the BGA on the first or second side through the furnace has always been controversial. Although placement on the second side can avoid the risk of remelting the tin and affecting its quality, the PCB will usually deform more seriously when the second side is passed through the reflow furnace. If the PCB is severely deformed, it can be a big problem for the delicate parts to be placed on the second side, because the solder paste printing position and the amount of solder paste will become inaccurate. Therefore, the focus should be to think of a way to avoid PCB distortion, instead of whether to put BGA on the first or second side.

Parts that cannot withstand overly high temperatures should be placed on the second side through the reflow furnace. This is to prevent parts from being damaged by high temperatures.

PIH/PIP parts should also be placed on the second side to pass through the furnace. Unless the length of the solder pin does not exceed the thickness of the board, the pin protruding from the PCB surface will interfere with the steel plate on the second side, so that the solder paste printed steel plate cannot be flatly attached to the PCB.

Some components may use soldering inside, such as a network cable connector with LED lights. It is necessary to pay attention to the temperature resistance of this part to pass the reflow oven twice. If it fails, it must be placed on the second side.

When parts are placed on the second side, it means that the circuit board has already been baptized by the high temperature of the reflow oven. At this time, the circuit board has become somewhat warped and deformed, which means that the tin quantity and printing position of the paste will become more difficult to control, so it is easy to cause problems such as empty soldering or short circuits. Therefore, it is recommended not to place 0201 and fine-pitch parts on the second side through the furnace. For BGA, try to choose a solder ball with a larger diameter.

In addition, in mass production, there are actually many process methods for soldering and assembling electronic parts on the circuit board, but each process is actually determined at the beginning of the circuit board design, because the placement of the parts will directly affect the soldering sequence and quality of the assembly, and the layout will be indirectly affected.

Soldering method of double-sided circuit board

In order to ensure the reliable conduction effect of the double-sided circuit board, the connection hole on the double-sided board (that is, the PTH) should be soldered with a wire, and the protruding part of the connection wire should be cut off to avoid stabbing the hand. This is in preparation for the wiring of the board.

The essentials of double-sided circuit board soldering

1. Devices that require reshaping should be processed according to the requirements of the process drawings:that is, reshaping first and then SMT.
2. The diode should face up after shaping, and there should be no discrepancyin the length of the two pins.
3. When inserting devices with polarity requirements, pay attention to ensure that their polarity is notreversed. Roll integrated block components after SMT. No matterwhether they are vertical or horizontal parts, there must be no obvious tilt.
4. The power of the iron used for soldering must bebetween 25~40W. The temperature of the soldering iron tip should be controlled at about 242℃. If the temperature is too high, the tip is close to useless,and the solder cannot be melted when the temperature is low. The soldering time is controlled at 3~4 seconds.
5. When soldering, generally follow the soldering principle of the device from short to high and from the inside to the outside. Thecorrectsoldering time must be mastered. If the time is too long, the device, as well as the circuits on the copper clad board, will be burnt.
6. Because the solderingis double-sided, a process frame for placing the circuit board should also be made, so as not to squeeze the components for the other side.
7. After the circuit board soldering is completed, a comprehensive check should be carried out to find any missing insertion orsoldering. After quality confirmation, trim the redundant device pins of the circuit board, and then go to the next process.
8. In anyspecific operation, the relevant process standards should be strictly followed to ensure the soldering quality of the product.

Re-soldering techniques for double-sided circuit boards

When re-soldering a double-sided circuit board, it is difficult to repair because it is dirty, messy, and may have faults such as false soldering, disconnection, and poor contact.

1. Observation: Based on drawings or prototypes, get a general understanding of the physical layout.
2. Dismantling: Remove the soldered components, pins andflying leads.
3. Cleaning: Use absolute alcohol to clean the rosin and soldering on the surface of the circuit board. When cleaning, if you use a soldering iron, it will be faster and the effect will be better.
4. Layout: Clarify the layout with reference to your observations. If there is no picture, use the drawing method to assist in annotation.
5. Soldering: Solder according to the clarifiedcircuits. When re-connecting circuit with circuit, try to arrange them on the back.
6. Inspection: According to the results of the drawing or prototype and the analysis of the layout, check whether the soldering is correct and reliable, and whether the process meets the requirements.
7. Power-on test.